package automation company

Package Automation Company
Solutions to Your Project Requirements

OUR PRODUCTS
DRUM/TOTE FILLING
 
      DF-5510 - Single Drum Filler
Drum Filling

This is a semi-automatic, sub-surface filler. This system requires empty drums to accumulate prior to the filling station. Bungs are removed and left on top of each drum, prior to filling. A scale mounted powered conveyor drives each drum on & off the fill station. The operator will replace the bung and place a cap or label while the next drum is filling. Full drums will convey to a palletizer, accumulate in-line or be picked-up by fork truck
Features
  • - Subsurface or top fill, 3 speed for greater accuracy
  • - Automatic abort if lance is not aligned with bung opening
  • - Two product flow valves to control water hammering
  • - Two inch diameter product valves for faster flow rates
  • - Quick change 2" diameter lance
  • - Wetted parts are 316 stainless steel with Teflon seats & seals
  • - 1000 lb capacity scale base with four load cells
   
     Stainless Fume Booth for Filling Systems
Drum Filling

This special, all 316 stainless steel fume booth and drum filler will fill hot liquids, at 300 degrees Fahrenheit, into 55 gallon steel drums. The station on the left is a drum filling station and fume collection booth. The operator station on the right is a cooling booth for the hot drum to dwell, with an air operated door between them. This system has an electric, heat jacketed lance to keep the liquid hot and flowing, a special funnel over the drum to collect fumes, a pull-out overflow pan under the filler, three air operated sliding doors with interlocks, a powered in/out conveyor system, thermal gloves for the operator and windows on the top, the sides, the back and in front.
   
     DTS-3500 - Automatic Pallet Dispenser & Collector
Tote Filling

This unique machine automatically dispenses pallets from the bottom of a stack at a rate of 2 pallets per minute. It uses air operated "dog type" clamps fitted for one size pallet. Capacity is 3500 pounds. A stack of 20 pallets can be inserted with an optional pallet magazine.
Features:
  • - Automatically dispenses pallets for the bottom every 30 seconds
  • - Lifting capacity: 3,500 lbs. pallet stack
  • - Stacking capacity: up to 20 same size pallets with optional magazine extension
  • - Dispensing rate:2 pallets per minute
  • - Air operated retractable "dog type" clamps capture the stack while an air operated lift deposits each pallet onto a discharge conveyor
  • - Fully Welded heavy-duty construction makes this the most durable pallet dispenser available.
   
     Turntables
Tote Filling
Typically used for load up to 4000 lbs. 90° turntables are air operated and 360° turntables are electric. These are fully welded structural steel units, pre-assembled, pre-wired and pre-piped. A variety of conveyors can be built on the surface. Special transition rollers are built for entry and exit points.
   
     Automatic Palletizer for Drums and Boxes
Drum Filling

This is a "pick and place" robot; ...a fully automated machine that lifts products from an infeed conveyor, carries them to a designated pallet position and gently places them down. This system can handle a variety of drums, boxes or other unitized loads. Each system is designed to suit.
Features:
  • - Robot carriage, chain driven with encoder.
  • - Robot lifted and lowered by pneumatics.
  • - Pallet Dispenser and Slip Sheet Dispenser included.
  • - All electro/pneumatic operation.
  • - Controlled by a P.L.C. in NEMA 12 panel.
  • - All prepiped, prewired and tested.
  • - Fully welded, heavy duty steel construction.
   
     Automatic Palletizer for Drums and Boxes
Drum Filling


Pails will be conveyed in line to an upstacker mechanism. The stacker will clamp and raise a pail sufficient to allow clearance for another to be conveyed under it. The second pail will also be clamped, them raised, allowing a third to move into position. This cycle repeats until four pails are properly stacked then conveyed out to allow the cycle to repeat. Each 4 pail stack stops in front of a horizontal pusher which slides each stack onto a stripper plate at the loading area.

A pallet will automatically discharge from a pallet dispenser onto a loading conveyor, then stop under the stripper plate to receive each four pail stack. After each pallet is loaded, it will convey downstream and a new pallet is dispensed into the same loading position.
   
     Special Pail Palletizer
Drum Filling

This is a fully automatic machine that creates a pallet load of pails 3 or 4 levels high every few minutes. The normal rate is 12 pails per minute but can be adjusted to 15 per minute. If necessary, we can accomodate up to 30 pails per minute by providing a second upstacker option.
Features:
  • - An air operated upstacker creates a column of pails.
  • - An air cylinder places each stack onto a stripper plate.
  • - When a row is ready, the stripper plate automatically lowers and retracts for gentle pallet loading.
  • - Overhead pneumatic hold down devices allow for stablizing loads at any stack height.
  • - Complete system includes automatic pallet dispenser, all electro/pneumatic operation, infeed and discharge conveyors all computer controlled.
   
 
Please email us for more information at info@pkgautomation.com